WB-MC
WB-MC - Image 2

WB-MC

Here you can find out more Vertriebsanfrage

Communicative interlinking of WB components

Category: Tags: , , ,

Description

The ‘WB-MC’ WB component enables remote components to communicate and network with one another. It also supports the exchange of information with third-party systems via standard protocols.

There are two typical areas of application:

1.) Communication link between a WITT Bridge measurement module and a higher-level SCADA system.

2.) Integration of various WB components for monitoring the cable infrastructure. Optionally, a WB-HS can monitor and configure everything centrally.

Product WB-MC variant:

  • CANOpen 1-channel 12mm
  • CANOpen 2 Canal 12mm
  • IEC 60870-5-103 / DIN EN 60870-5-103
  • IEC 60870-5-104 / DIN EN 60870-5-104
  • IEC 61850
  • ModBus/TCP
  • ModBus/RTU
  • PROFIBUS
  • Other variants available on request

Function

The WB-MC component is connected to the WB backplane bus with third WB components. The WB component “translates” information from the WB components connected to the backplane bus and the external protocol.

Depending on the protocol used and the WB components, a wide variety of quantities and information can be transmitted:

  • operational status
  • control commands
  • real value
  • target values
  • event-based transmission
  • no “real-time” transmissions

Technical data

Product WB-MC variant:

  • CANOpen 1-channel 12mm

  • CANOpen 2 Canal 12mm

  • IEC 60870-5-103 / DIN EN 60870-5-103

  • IEC 60870-5-104 / DIN EN 60870-5-104

  • IEC 61850

  • ModBus/TCP

  • ModBus/RTU

  • PROFIBUS

  • Other variants available on request

Galvanic isolation in each case

  • up to 4 kV

  • up to 1,5 kV

  • low, depending on the communication method

Analogue input channels (measurement channels)

NONE

Digital input channels

NONE

Digital output channels

NONE

Advertisements

Possible variants depending on the range of functions or options

LED

Color

Labelling

Description

1

green

Run

Continuous ON: Operational status

2

green

Run

Continuous ON: Operational status

Flashing: The component is booting up and connecting to the backplane bus and external units

3

red

Error

Malfunction of the system, sensors or equipment

parameterisation

“Configuration profiles” are stored in the CM1010 / VLD1010 service kit and transferred to the WB component.

Contents

  • User manual

  • Installation instructions

  • WB component / printed circuit board

  • Packaging

  • Test report

Communication

The following digital values can be transmitted by the component to third-party systems or retrieved by third parties.
The options listed are dependent on the component, configuration, installed options, system architecture and the protocol used.

Values- Output

Input values

Operating status

  1. Error with error code
  2. Run
  3. Standby
  4. Automatik

Command

  1. Perform a self-test
  2. Reset System
  3. Reset Schaltcounter
  4. Reset measuring tips
  5. Switch to standby mode
  6. Switch to automatic mode

Digital Values

The following digital values ​​can be passed on by the components to third-party systems or queried by third parties.
Possibilities are also listed depending on the components, configuration, installed options and system structure as well as the protocol used.

values- output

  1. Product type including extension
  2. Serial number including the extension
  3. Article number
  4. Soft and hardware versions
  5. Type protocol and its configuration

values ​​input

  1. Parameters for configuring the installed protocol

operational status

  1. Error with error code
  2. Run
  3. Standby
  4. Automatic

Command

  1. Perform self-test
  2. Reset System
  3. Reset switch counter
  4. Switch to standby mode
  5. Switch to automatic mode

Related products